Cisco Configuration Validator
Paste a Cisco IOS or IOS XE configuration and get structured findings for interface conflicts, EtherChannel and VLAN problems, duplicate SVI addresses, and disruptive commands. Runs entirely in your browser.
Cisco Configuration Validator
Configuration analysis runs locally in your browser. Pasted configurations are not sent to NetworkToolsHub servers.
Configuration
What this tool checks
- Interface stanzas, access and trunk modes, access, voice, and native VLANs, and allowed-VLAN lists.
- EtherChannel membership, including one interface joining two channel groups and member/Port-channel VLAN mismatches.
- VLAN definitions, ranges, and references, with command order preserved.
- SVI IPv4 addresses: duplicates, overlapping subnets, invalid masks, network or broadcast misuse, and /31 and /32 handling.
- Disruptive commands such as reload, write erase, default interface, shutdown, and allowed-list replacement, classified by context.
What it does not check
- ACLs, QoS, routing protocols, SPAN, and hardware-specific features are not fully validated.
- It cannot see your device: a VLAN absent from the paste may exist on the switch already.
- It does not replace Cisco configuration validation, change review, or testing on the target platform.
Findings are labeled confirmed or potential. Potential findings and incomplete-context flags mean the pasted snippet alone cannot prove the problem. Command order matters: later commands override earlier ones, and the validator reads them in order.
How to use the validator
Paste the interface and vlan sections you want reviewed, then choose Validate Configuration. Load one of the three built-in examples to see the kind of findings the tool reports. Everything is analyzed locally.
Detecting duplicate SVI addressing
Load the duplicate SVI example. Two SVIs share the address 10.20.30.1, so the validator reports a duplicate address (CV-IP-003) and an overlapping connected subnet (CV-IP-004), each pointing at the source line of the second SVI. On a real switch this combination causes inter-VLAN traffic to reach the wrong interface.
Detecting an EtherChannel conflict
Load the EtherChannel example. TenGigabitEthernet1/1/1 joins both channel-group 10 and channel-group 20, which IOS cannot honor. The validator reports a confirmed error (CV-EC-001) at the line of the second channel-group command, with the first line listed as related context.
Reading the findings
- Errors are definite problems in the pasted text.
- Warnings are worth reviewing but can be intentional.
- Informational findings describe behavior, not mistakes.
- Confirmed findings are provable from the paste; potential ones are not.
- Incomplete context means the snippet alone cannot establish the full picture.
Why command order matters
IOS applies commands in order, and later commands override earlier ones. A port that is shut down and then re-enabled ends up enabled, so the validator reports the effective state instead of flagging a conflict. The same logic distinguishes an allowed-VLAN replacement from an add or remove.
Supported and unsupported syntax
The validator parses interface stanzas, vlan blocks, switchport settings, channel-group commands, SVI addressing, and the safety commands listed in the findings. It does not fully validate ACLs, QoS, routing protocols, SPAN, or hardware-specific features, and interface ranges are recognized but not expanded for per-interface analysis. Unsupported lines are listed in their own section, and being listed there is not an error.
Related tools
- Cisco VLAN & SVI Generator — build the VLANs and SVIs to validate
- Cisco ACL Builder & Analyzer — build and analyze the ACLs this validator does not check
- Cisco Switchport & Trunk Generator — generate ports and trunks before validating them
- VLAN Sizing Calculator — size each VLAN subnet
- VLSM Calculator — allocate subnets for each VLAN
Frequently Asked Questions
Is my configuration uploaded anywhere?
No. Analysis runs locally in your browser. The pasted text is not sent to NetworkToolsHub servers, is not written to analytics, and is not included in exports unless you tick the box that adds it.
What is the difference between an error, a warning, and an informational finding?
An error is a definite problem in the pasted text, such as one interface joining two channel groups. A warning is worth reviewing but may be intended, like repeated interface stanzas. Informational findings describe behavior you should be aware of, like an allowed-VLAN list replacement, and are not mistakes.
What do the confidence and incomplete-context labels mean?
Confirmed findings are provable from the pasted text alone. Potential findings, and those marked incomplete-context, depend on things the snippet cannot show, such as VLANs that already exist on the switch. Confirm them against the device before acting.
Why does a partial snippet produce different results than the full configuration?
The validator reads only what you paste. A VLAN used by an interface but never defined in the snippet is reported as potentially missing, not definitely missing, because it may already be on the switch. Paste the vlan blocks too for a more complete check.
Does a clean result mean the configuration is safe to apply?
No. Zero findings means the validator saw no recognized problems in the supported syntax. It cannot check hardware or software compatibility, ACLs, QoS, routing protocols, or SPAN, and it never replaces change review or testing on the target platform.
Technically Reviewed By
Senior Enterprise Network Engineer — 25+ years of IT and network infrastructure experience, including enterprise Cisco switching, routing, wireless, firewalls, VPN, network access control, SD-WAN, and large-scale network operations.
Calculations are performed using standards-based formulas and verified against known reference values. All computation runs client-side in your browser.
Related Resources
Cisco VLAN Config Generator
Generate Cisco IOS-XE VLAN configuration including VLAN ID, name, SVI IP, subnet mask, description, and DHCP relay addresses.
Cisco Switchport & Trunk Config Generator
Generate Cisco IOS and IOS XE switchport configuration for access ports, standalone trunks, Port-channel interfaces, and EtherChannel members, with interface range grouping and copy or download output.
VLAN Sizing Calculator
Determine the right subnet size for a VLAN based on current clients, growth percentage, and reserved infrastructure addresses.
VLSM Calculator & Subnet Planner
Plan VLSM subnets from a parent network. Enter multiple host requirements and automatically allocate non-overlapping, right-sized subnets with largest-first allocation, address-space visualization, CSV export, and print.