Cisco Switchport & Trunk Config Generator
Generate Cisco IOS and IOS XE switchport configuration for access ports, standalone trunks, Port-channel interfaces, and EtherChannel members, with interface range grouping and copy or download output.
Platform and options
VLANs from other tools
Loaded VLANs appear as suggestions in the VLAN fields below. Typing any VLAN ID still works.
No VLANs loaded. Use Send to Switchport Generator in the Multi-VLAN Planner or the Cisco VLAN & SVI Generator to load them here, or type VLAN IDs by hand.
Interfaces
Add one entry per interface. Member interfaces join a Port-channel, so set the Port-channel itself as its own entry.
Interface 1
Full name, such as GigabitEthernet1/0/10.
Optional.
Optional.
Turn these on only when a host or phone is the only device expected on this port.
Only where the port supports it.
Only where the port supports it.
Existing configuration (optional)
Paste the output of a show command for the interfaces you are changing. The text is only read as plain text. It is never run.
0 of 16,384 characters
Configuration output
Fix the errors above to generate configuration. Each interface needs a valid name and role-specific settings.
Access ports and trunks
An access port carries one VLAN, which is what a PC, printer, or IP phone expects. A trunk carries several VLANs at once, tagged so the far end knows which VLAN each frame belongs to. Switch-to-switch and switch-to-router links are normally trunks. Hosts are normally access ports.
Native and voice VLANs
The native VLAN on a trunk carries untagged frames. Both ends of the trunk must agree on it, or traffic can leak between VLANs. A voice VLAN on an access port lets a phone tag its voice traffic while the attached PC stays on the access VLAN. The voice VLAN must differ from the access VLAN, and the generator blocks identical values.
PortFast and BPDU Guard
- PortFast lets a port skip spanning-tree listening and learning, so a host connects without a delay. Use it only on ports where a single end device connects.
- BPDU Guard shuts a PortFast port down if a switch is plugged into it. This protects the network from an accidental loop, and it pairs well with PortFast on host ports.
- Never enable PortFast on a switch-to-switch uplink.
Allowed VLAN lists are replaced, not added to
switchport trunk allowed vlan sets the complete list of VLANs a trunk carries. Entering 10,20 removes VLAN 30 from the trunk if it was previously allowed. Compare the list with the current trunk before applying it. The generator warns whenever a trunk command is produced for this reason.
Port-channels and EtherChannel members
An EtherChannel bundles several physical links into one logical link. The logical interface, called Port-channel, holds the VLAN settings. Each physical member joins it with a channel-group command and takes its VLAN settings from the Port-channel. Set native and allowed VLANs on the Port-channel entry, not on its members.
LACP (802.3ad) negotiates the bundle. Active mode starts negotiation, and passive mode only responds. Both ends of a bundle must match in speed, duplex, and VLAN settings, or the bundle will not form cleanly.
Interface ranges
Ports with identical settings and consecutive numbers can be grouped into a single interface range block. Grouping is limited to access and trunk ports. Port-channels and members are always written individually, so a channel change never applies to a whole range by accident. Ports with differing descriptions or settings are not grouped.
Working on live links
- Changing a trunk's allowed VLANs or joining a link to a channel group can interrupt live traffic.
- Apply uplink and Port-channel changes in a planned window, one link at a time where the design allows.
- Keep the current configuration of each interface so you can roll back.
- Check that the VLANs exist on the switch (see the VLAN and SVI generator) before allowing them on a trunk.
Before you apply the configuration
- Confirm the interface names match your switch model, including slot and module numbers.
- Confirm the platform supports each speed, duplex, and channel setting you chose.
- Use the existing configuration panel to spot interfaces already in a channel group.
- Check the channel group number is free or already defined as the same Port-channel.
Common mistakes
- Setting VLANs on members: the Port-channel controls them, so configure the logical interface.
- Forgetting the allowed list is a replacement: a short list silently removes VLANs from a trunk.
- PortFast on uplinks: a switch-facing port with PortFast can create a loop before spanning tree converges.
- Mismatched LACP modes: two passive ends never form a bundle.
Technical references
- IEEE 802.1Q — VLAN tagging for bridged and virtual bridged LANs (trunk encapsulation).
- IEEE 802.1AX — Link Aggregation (EtherChannel with LACP).
- Cisco IOS and IOS XE command reference: search Cisco documentation for
switchport trunk allowed vlan,channel-group, andinterface rangefor the software release on your device.
Related tools
- Cisco VLAN & SVI Generator — create the VLANs your ports will use
- VLAN Sizing Calculator — size each VLAN before assigning ports
- Multi-VLAN Planner — plan VLAN IDs and names
- Cisco Configuration Validator — check a pasted configuration for conflicts
Frequently Asked Questions
Does this tool connect to my switch or apply the configuration?
No. The generator only builds text in your browser. It does not connect to any device, store credentials, or deploy anything. You review the output and apply it yourself through your normal change process.
Can I paste my current configuration to check for conflicts?
Yes. Paste the interface sections for the ports you are changing. The generator reads them as plain text only and never runs them. It flags interfaces that already belong to a channel group, and it warns about lines it cannot read rather than guessing.
What is the difference between a Port-channel and an EtherChannel member?
A Port-channel is the logical interface that holds VLAN settings for a bundle of links. An EtherChannel member is a physical interface that joins the bundle through a channel-group command. Set VLANs on the Port-channel, and set only the channel group and LACP mode on each member.
Why does the allowed VLAN list warn me so often?
On a Cisco trunk, the allowed VLAN command replaces the entire list. Any VLAN left out stops crossing the trunk as soon as the command is applied. Compare the list with the trunk's current state before you change it on a live link.
Can I put every port into one interface range?
Only access and trunk ports with identical settings and consecutive numbers are grouped. Port-channels and EtherChannel members are always written individually so a channel change cannot apply to a range by accident. Turn range grouping off to get one block per interface.
Technically Reviewed By
Senior Enterprise Network Engineer — 25+ years of IT and network infrastructure experience, including enterprise Cisco switching, routing, wireless, firewalls, VPN, network access control, SD-WAN, and large-scale network operations.
Calculations are performed using standards-based formulas and verified against known reference values. All computation runs client-side in your browser.
Related Resources
Cisco VLAN Config Generator
Generate Cisco IOS-XE VLAN configuration including VLAN ID, name, SVI IP, subnet mask, description, and DHCP relay addresses.
VLAN Sizing Calculator
Determine the right subnet size for a VLAN based on current clients, growth percentage, and reserved infrastructure addresses.
VLAN Calculator
Plan VLAN IDs, assign subnets, and generate VLAN-to-subnet mapping tables for multi-VLAN environments.
Cisco Configuration Validator
Paste a Cisco IOS or IOS XE configuration and get structured findings for interface conflicts, EtherChannel and VLAN problems, duplicate SVI addresses, and disruptive commands. Runs entirely in your browser.
Cisco Interface Config Generator
Generate Cisco IOS-XE interface configuration CLI for access, trunk, and routed ports with VLAN, description, and QoS options.