PoE Budget Calculator

Calculate total PoE power consumption, remaining budget, utilization, and maximum devices for 802.3af/at/bt switches.

Built by a network engineerCalculations run locally in your browserNo signup requiredNetwork information is not transmitted to our servers

PoE Budget Calculator

Connected Devices

Results

Total PoE Consumption
32.0 W
Remaining PoE Budget
338.0 W
Utilization
8.6%
Max Additional Devices
46
Limiting Factor
Port count

PoE Budget Utilization

8.6%
0 W80% (296 W)370 W

Limiting factor: physical port count. You have enough PoE power but not enough PoE-capable ports for more devices.

What the PoE Budget Calculator Does

The PoE (Power over Ethernet) budget calculator helps network engineers ensure that a switch’s PoE power budget can support all connected PoE devices. Enter the switch’s total PoE budget in watts, total and PoE-capable port counts, then add devices with their count and per-device wattage. The calculator shows total consumption, remaining budget, utilization percentage, how many additional devices the switch can support, and whether the limiting factor is port count or available power.

How the Calculation Works

Total consumption is the sum of each device’s count multiplied by its wattage. Remaining budget is the switch budget minus total consumption. Utilization is total consumption divided by the switch budget, expressed as a percentage. The calculator compares the maximum additional devices by power budget versus by available PoE ports, and reports which factor is limiting. Warning indicators appear at 60% (caution), 80% (warning), 90% (critical), and 100% (exceeded).

IEEE PoE Standards

The calculator distinguishes between PSE (Power Sourcing Equipment) output and PD (Powered Device) input, since cable loss means the device receives less power than the switch delivers:

  • 802.3af (Type 1): 15.4W PSE output, 12.95W at PD
  • 802.3at (Type 2, PoE+): 30W PSE output, 25.5W at PD
  • 802.3bt (Type 3): 60W PSE output, 51W at PD
  • 802.3bt (Type 4): 90W PSE output, 71.3W at PD

When entering device wattage, use the actual power draw of the device (PD input), not the PSE output. The switch budget should match the PSE total budget from the datasheet.

Example

A 48-port switch with 370W PoE budget (all ports PoE-capable) powering 8 access points at 25W each and 20 IP phones at 7W each:

  • Total consumption: 340W (200W + 140W)
  • Remaining budget: 30W
  • Utilization: 91.9% (critical)
  • Limiting factor: PoE power (28 ports used of 48, but only 30W remaining)
  • Max additional devices: 1 (at 25W each, limited by power not ports)

Common Use Cases

  • Selecting a switch with adequate PoE budget before deployment
  • Validating that existing switches can support additional access points or cameras
  • Planning capacity for IP phone rollouts
  • Balancing PoE load across multiple switches in a closet
  • Determining whether port count or power budget is the constraint

Important Considerations

PoE budget is separate from port count — a 48-port switch may not have enough power to run 48 PoE devices at full wattage. Cable length affects delivered power due to resistance; longer runs deliver slightly less power to the device. Some devices draw more power during startup (e.g., motorized PTZ cameras). The PSE output rating is higher than the PD input rating due to cable loss — always check which value you are using. Always check the switch datasheet for the total PoE budget, not just the per-port maximum, and consider power supply redundancy for critical infrastructure.

Frequently Asked Questions

What is the difference between 802.3af, 802.3at, and 802.3bt?

802.3af delivers up to 15.4W per port, 802.3at (PoE+) up to 30W, and 802.3bt (PoE++) up to 90W. Higher standards support more power-hungry devices like PTZ cameras and 802.11ax access points.

Why is my switch's PoE budget lower than port count times max wattage?

Switches have a total power budget shared across all ports. A 48-port switch with 802.3at (30W) support may only have a 740W budget, which is not enough to run all 48 ports at full 30W simultaneously.

What happens when PoE utilization exceeds 80%?

At 80% utilization, you have limited headroom for adding devices. At 90%, you risk power budget exhaustion. At 100%, new devices will not receive power and existing devices may experience power interruptions.

Technically Reviewed By

Senior Enterprise Network Engineer — 25+ years of IT and network infrastructure experience, including enterprise Cisco switching, routing, wireless, firewalls, VPN, network access control, SD-WAN, and large-scale network operations.

Last reviewed: 2026-09-04

Calculations are performed using standards-based formulas and verified against known reference values. All computation runs client-side in your browser.

Related Resources