DHCP Scope Calculator
Calculate DHCP scope ranges, available addresses, exclusions, reservations, and utilization for IPv4 networks.
DHCP Scope Calculator
Gateways, servers, printers, and other static assignments.
Results
- Network Address
- 192.168.1.0
- Subnet Mask
- 255.255.255.0
- Broadcast Address
- 192.168.1.255
- Total Addresses
- 256
- Reserved Addresses
- 3
- Excluded Addresses
- 0
- Available for DHCP
- 251
- Recommended DHCP Range
- 192.168.1.3 - 192.168.1.253
- DHCP Start
- 192.168.1.3
- DHCP End
- 192.168.1.253
- Utilization
- 79.7%
Recommendation: Keep DHCP utilization below approximately 80%. This ensures enough addresses are available for new devices and prevents scope exhaustion during peak usage.
Advanced Scope Planning
Servers, switches, and other static devices. One address or range per line.
Addresses the DHCP server must never lease. One address or range per line.
DHCP Scope Results
- Network Address
- 10.20.30.0/24
- Subnet Mask
- 255.255.255.0
- Broadcast Address
- 10.20.30.255
- Total Addresses
- 256
- Usable Host Addresses
- 254
- Gateway
- 10.20.30.1
- Reserved Infrastructure Addresses
- 20
- Excluded Addresses
- 11
- Total Available DHCP Addresses
- 234
- DHCP Capacity After Exclusions
- 223
- Lowest Eligible DHCP Address
- 10.20.30.21
- Highest Eligible DHCP Address
- 10.20.30.254
- Requested Clients (including growth)
- 216
- Remaining DHCP Capacity
- 7
- Utilization
- 96.9%
- Available DHCP Range 1
- 10.20.30.21 - 10.20.30.99
- Available DHCP Range 2
- 10.20.30.111 - 10.20.30.254
Assignable DHCP Ranges
The pool is not one continuous block when exclusions are present. Only the addresses inside these ranges can be leased, and every address between them is excluded.
- 10.20.30.21 - 10.20.30.99
- 10.20.30.111 - 10.20.30.254
DHCP Lease Planning
The lease duration of 24 hours controls how long a client keeps an address before it must renew (RFC 2131). A shorter lease returns addresses to the pool sooner, so they can be reused by new clients. Lease duration does not increase the number of addresses in the subnet; the 223 assignable addresses are fixed by the prefix and exclusions.
Daily unique clients do not reveal how many leases are active at the same time, so this is an informational check only.
Cisco IOS DHCP Configuration Preview
Only enable this if a Cisco IOS or IOS XE router or switch will serve DHCP for this subnet. If another server handles DHCP, leave this off.
What the DHCP Scope Calculator Does
The DHCP scope calculator helps network engineers plan and validate DHCP address pools. Given a network address, CIDR prefix, reserved IPs, exclusions, and the expected number of clients, it calculates the recommended DHCP range, available addresses, utilization percentage, and warns when the scope is undersized.
How the Calculation Works
The calculator first determines the total address space from the CIDR prefix, then subtracts the network address, broadcast address, reserved IPs, and excluded addresses to find the pool available for DHCP. The utilization percentage is the desired client count divided by the available DHCP addresses. If utilization exceeds your target (default 80%), a warning is displayed recommending a larger subnet or fewer reservations.
Example
For network 192.168.1.0/24 with 3 reserved IPs and 200 desired clients:
- Total addresses: 256
- Available for DHCP: 251 (256 - 2 network/broadcast - 3 reserved)
- Utilization: 79.7%
- Recommended range: 192.168.1.3 - 192.168.1.253
Common Use Cases
- Planning DHCP scopes for new VLANs or office networks
- Validating that an existing scope has enough addresses for expected growth
- Determining the right subnet size based on client count and reservations
- Identifying when to split or expand a DHCP scope
Important Considerations
DHCP utilization should generally stay below 80% to accommodate peak usage and short-term address leases. Devices like phones, tablets, and guest laptops can generate high lease churn. Consider lease time tuning (shorter leases for busy networks, longer for stable ones) and DHCP failover or split scopes for high-availability deployments. Always coordinate DHCP scope planning with your IP addressing scheme and VLAN strategy.
DHCP Scope Planning
A DHCP scope is the pool of addresses a DHCP server can lease to clients on one subnet. Good scope planning starts with the subnet size, then removes every address that must never be leased to a client: the gateway, static infrastructure, and any ranges you exclude. Only what remains is available for dynamic allocation. Plan the subnet itself with the Subnet Calculator and the VLSM Calculator before you build the scope.
DHCP Exclusions Versus Reservations
These two terms describe different things and should not be used interchangeably. An exclusion removes an address from the dynamic pool for the whole scope, so the DHCP server never hands it to any client. A reservation maps one client, usually identified by its MAC address or client identifier, to one specific IP address, so that client always receives that address. Reservations are per client; exclusions apply to the pool as a whole.
The "Reserved Infrastructure Addresses" field in this planner lists static devices, such as servers, switches, and printers, that must never be leased. On Cisco IOS these become ip dhcp excluded-address commands. Any per-device mapping is a separate DHCP reservation and is not counted here.
Gateway Exclusions
The default gateway is configured statically on a router or Layer 3 interface. It must be excluded from the DHCP scope. If it is not, a client can be leased the gateway's address, which causes an IP address conflict and breaks routing for that client. This planner never counts the gateway twice, even if it also appears in your exclusions.
DHCP Address Exhaustion
When every address in a scope is leased, the DHCP server cannot answer new requests. New devices then fail to get an address. Windows clients typically self-assign a 169.254.0.0/16 address, which cannot reach the rest of the network. Exhaustion is most often caused by a scope that was sized for today's devices with no room for growth, or by long leases held by devices that have left the network. Keep utilization below roughly 80% to leave room for peaks.
Lease Duration
Under RFC 2131, a DHCP lease is the period for which a client may use an address. The client renews at half the lease time and, if renewal fails, tries again at 87.5% of the lease time. Shorter leases return addresses to the pool sooner, which helps busy networks such as guest Wi-Fi. Longer leases reduce DHCP traffic on stable networks. Lease duration changes how often addresses are reused; it does not create more addresses. Use the Subnet Overlap Checker to confirm that scopes on neighboring networks do not overlap.
DHCP Relay (ip helper-address)
DHCP clients broadcast their requests, and broadcasts do not cross routers by default. When the DHCP server is on a different subnet, a relay agent forwards the request to the server as a unicast message. On Cisco IOS, configure this on the client VLAN's interface with ip helper-address <dhcp-server-ip>. The relay behavior is described in RFC 2131 and in the BOOTP relay model of RFC 1542. Remember that the relay forwards to the server, but the server still needs a scope that covers the client's subnet.
Growth Planning
Plan for the clients you expect in the next planning period, not just today. The growth percentage in this planner adds headroom on top of the current client count. If the requested clients plus growth exceed the assignable addresses, the planner shows the shortage and suggests a larger prefix. Any change to an existing production subnet has side effects, so confirm the gateway, DHCP, and routing impact before you renumber. For VLAN-level sizing, see the VLAN Sizing Calculator.
Client Turnover
Client turnover is the rate at which new devices join and old ones leave. Phones, tablets, and guest laptops can make many more unique clients per day than are connected at any moment, so a small scope can still work well if leases are short. The unique-clients-per-day estimate in this planner is only an informational check. It does not predict how many leases are active at the same time.
Frequently Asked Questions
What is a good DHCP utilization percentage?
Keep DHCP utilization below approximately 80%. This ensures enough addresses are available for new devices and prevents scope exhaustion during peak usage.
How are reserved IPs different from exclusions?
Reserved IPs are addresses assigned to static devices like gateways, servers, and printers. Exclusions are addresses the DHCP server should not lease, which may include reserved IPs or addresses outside the DHCP pool.
What happens when my DHCP scope is undersized?
When utilization exceeds your target, new devices may fail to obtain IP addresses. Solutions include using a larger subnet, reducing reservations, shortening lease times, or implementing DHCP failover.
Technically Reviewed By
Senior Enterprise Network Engineer — 25+ years of IT and network infrastructure experience, including enterprise Cisco switching, routing, wireless, firewalls, VPN, network access control, SD-WAN, and large-scale network operations.
Last reviewed: 2026-09-04
Calculations are performed using standards-based formulas and verified against known reference values. All computation runs client-side in your browser.
Related Resources
Subnet Calculator
Calculate IPv4 network addresses, broadcast addresses, subnet masks, CIDR ranges, wildcard masks, and usable hosts.
VLAN Sizing Calculator
Determine the right subnet size for a VLAN based on current clients, growth percentage, and reserved infrastructure addresses.
VLSM Calculator & Subnet Planner
Plan VLSM subnets from a parent network. Enter multiple host requirements and automatically allocate non-overlapping, right-sized subnets with largest-first allocation, address-space visualization, CSV export, and print.
IP Subnet Overlap Checker
Detect overlapping, duplicate, and contained IPv4 subnets. Paste multiple CIDR networks to identify every conflicting pair with clear explanations and CSV export.
Cisco DHCP Config Generator
Generate Cisco IOS-XE DHCP pool configuration including network, default-router, DNS, lease time, and excluded addresses.
Cisco VLAN Config Generator
Generate Cisco IOS-XE VLAN configuration including VLAN ID, name, SVI IP, subnet mask, description, and DHCP relay addresses.
CIDR Calculator
Convert CIDR notation to subnet masks, wildcard masks, and calculate usable IP ranges with an interactive slider.
IPv4 Subnetting Guide
A complete walkthrough of IPv4 subnetting: network vs host bits, CIDR notation, calculating network addresses, broadcast addresses, and usable hosts with worked examples.
RFC 1918 Private IP Address Ranges
The three private IP ranges defined by RFC 1918, how to use them, and why they matter for internal network design and NAT.