Ethernet Speed Reference

Ethernet standards from 10 Mbps to 400 Gbps, including the IEEE 802.3 designation, cable type, maximum distance, and connector. Copper (RJ-45 and DAC) and optical variants are listed.

Built by a network engineerCalculations run locally in your browserNo signup requiredNetwork information is not transmitted to our servers

IEEE 802.3 Ethernet Standards

Distances for fiber optics depend on the fiber grade (see the Fiber Optic Reference). OM4 multimode distances are shown where applicable; OM1/OM2/OM3 will be shorter. Single-mode distances assume standard OS2 fiber without amplification.

StandardIEEESpeedCable TypeMax DistanceConnector
10Base-T802.3i10 MbpsCat3+ UTP100 mRJ-45
100Base-TX802.3u100 MbpsCat5/5e UTP100 mRJ-45
100Base-FX802.3u100 MbpsMultimode fiber2 km (62.5/125 µm)SC, LC
1000Base-T802.3ab1 GbpsCat5e/6 UTP100 mRJ-45
1000Base-SX802.3z1 GbpsMMF (850 nm)550 m (OM4)LC
1000Base-LX802.3z1 GbpsSMF/MMF (1310 nm)5 km (SMF) / 550 m (MMF)LC
1000Base-ZX802.3z1 GbpsSMF (1550 nm)70 kmLC
10GBase-T802.3an10 GbpsCat6a/7 UTP100 m (Cat6a)RJ-45
10GBase-SR802.3ae10 GbpsMMF (850 nm)400 m (OM4)LC
10GBase-LR802.3ae10 GbpsSMF (1310 nm)10 kmLC
10GBase-ER802.3ae10 GbpsSMF (1550 nm)40 kmLC
10GBase-ZR802.3ae10 GbpsSMF (1550 nm)80 kmLC
25GBase-CR802.3bq25 GbpsTwinax copper5 mSFP28 DAC
25GBase-SR802.3by25 GbpsMMF (850 nm)100 m (OM4)SFP28
25GBase-LR802.3by25 GbpsSMF (1310 nm)10 kmSFP28
40GBase-CR4802.3ba40 GbpsTwinax copper7 mQSFP+ DAC
40GBase-SR4802.3ba40 GbpsMMF (850 nm, 4 lanes)100 m (OM4)QSFP+ MPO
40GBase-LR4802.3ba40 GbpsSMF (4 × CWDM)10 kmQSFP+ LC
100GBase-CR4802.3bj100 GbpsTwinax copper5 mQSFP28 DAC
100GBase-SR4802.3bm100 GbpsMMF (850 nm, 4 lanes)100 m (OM4)QSFP28 MPO
100GBase-LR4802.3ba100 GbpsSMF (4 × WDM)10 kmQSFP28 LC
100GBase-ER4802.3bm100 GbpsSMF (4 × WDM)40 kmQSFP28 LC
200GBase-CR4802.3cd200 GbpsTwinax copper3 mQSFP56 DAC
200GBase-SR4802.3cd200 GbpsMMF (850 nm)100 m (OM4)QSFP56 MPO
400GBase-DR4802.3bs400 GbpsSMF (4 × 100G)500 mQSFP-DD MPO
400GBase-FR4802.3bs400 GbpsSMF (4 × CWDM)2 kmQSFP-DD LC
400GBase-LR4802.3bs400 GbpsSMF (4 × WDM)10 kmQSFP-DD LC

Notes

DAC (Direct Attach Copper) cables are passive or active twinax assemblies used for short-reach top-of-rack to server connections. They trade distance for low cost and latency. Multi-lane optics (SR4, LR4, etc.) use parallel fibers or wavelength-division multiplexing to achieve higher aggregate speeds.

10GBase-T over Cat6 (non-a) is limited to 55 m at full speed; Cat6a is required for the full 100 m. Backplane Ethernet variants (10GBase-KR, 40GBase-KR4) are used inside chassis switches and are not cabled externally.

Related Tools

Technically Reviewed By

Senior Enterprise Network Engineer — 25+ years of IT and network infrastructure experience, including enterprise Cisco switching, routing, wireless, firewalls, VPN, network access control, SD-WAN, and large-scale network operations.

Last reviewed: 2026-09-02

Calculations are performed using standards-based formulas and verified against known reference values. All computation runs client-side in your browser.